Sensitive Two-Wire Chopper-Stabilized
Unipolar Hall Effect Switches
A1140, A1142, and
A1143
10
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Power Derating
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
qJA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
qJC
, is
relatively small component of R
qJA
. Ambient air temperature,
T
A
, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
?/DIV>
I
IN
(1)
DT = P
D
?/DIV>
R
qJA
(2)
T
J
= T
A
+ 擳 (3)
For example, given common conditions such as: T
A
= 25癈,
V
CC
= 12 V, I
CC
= 4 mA, and R
qJA
= 140 癈/W, then:
P
D
= V
CC
?/DIV>
I
CC
= 12 V
?/DIV>
4 mA = 48 mW
DT = P
D
?/DIV>
R
qJA
= 48 mW
?/DIV>
140 癈/W = 7癈
T
J
= T
A
+ DT = 25癈 + 7癈 = 32癈
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level (V
CC(max)
, I
CC(max)
), without exceeding T
J(max)
,
at a selected R
qJA
and T
A
.
Example: Reliability for V
CC
at T
A
=
150癈, package UA, using
minimum-K PCB.
Observe the worst-case ratings for the device, specifically:
R
qJA
=
165癈/W, T
J(max)
=
165癈, V
CC(max)
=
24 V, and
I
CC(max)
=
17
mA.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
DT
max
= T
J(max)
T
A
= 165
癈
150
癈 = 15
癈
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
= DT
max
?R
qJA
= 15癈 ?165 癈/W = 91 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
? I
CC(max)
= 91 mW ?17 mA = 5 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages dV
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
d V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
qJA
. If V
CC(est)
e V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
A1146LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1148LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1155LUA-T
IC SW HALL EFFECT CHOPPER 3SIP
A1180LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1184LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1186LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1193LUA-T
IC SW HALL EFFECT CHOPPER 3SIP
A1203LUA-T
IC SW CONTINUOUS TIME BIPO 3-SIP
相关代理商/技术参数
A1143LUATI-T4
制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches
A11442MNZQ
制造商:ITT 制造商全称:ITT Industries 功能描述:1-4 Pole Rotary Switches
A11442MSZQ
制造商:ITT 制造商全称:ITT Industries 功能描述:1-4 Pole Rotary Switches
A11442RNZQ
制造商:ITT 制造商全称:ITT Industries 功能描述:1-4 Pole Rotary Switches
A11442RSZQ
制造商:ITT 制造商全称:ITT Industries 功能描述:1-4 Pole Rotary Switches
A1145
制造商:Hakko 功能描述:Heating Element for Hakko 850
A1145_06
制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches
A1145-10
制造商:ELCCUB 功能描述: 制造商:ELECTROCUBE INC DBA ELECT 功能描述: